Home » SHOP ALL: GOLD BALLARAT PROSPECTING EQUIPMENT » MINELAB DETECTOR HELP GUIDES » MINELAB GPX 6000 HELP GUIDES

MINELAB GPX 6000 HELP GUIDES

MINELAB GPX 6000

Powered by GeoSense-PI™ technology, the Minelab GPX 6000 is the fastest, lightest and simplest way to find all types of gold in one machine.

Instruction Manual GPX 6000 A4 (EN) - 2.45 MB

MINELAB GPX 6000 WHATS IN THE BOX

Unboxing of the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 HOW TO SET UP YOUR DETECTOR

Learn how to set up the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 HOW TO CHANGE THE BATTERY

Learn how to charge the battery on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 HOW TO GET STARTED QUICKLY

Learn how to get started quickly with the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 HOW TO ADJUST THE VOLUME & BACKLIGHT

Learn how to adjust the volume and backlight on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 HOW TO CONNECT THE BLUETOOTH HEADPHONES

Learn how to connect the ML100 Wireless Headphones to the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 INTELLIGENT AUTOMATIC OPERATION

Learn how to reduce unwanted interference when the MINELAB GPX 6000 is configured for intelligent automatic operation.

MINELAB GPX 6000 AUTOMATIC SENSITIVITY

Learn about Automatic Sensitivity on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 COILS

Learn about the three coil options for the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 DOUBLE D EMI NOISE CANCEL FEATURE

Learn how to perform a Double-D EMI Noise Cancel on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 ADVANCED GROUND BALLANCE

Learn about advanced Ground Balance on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 USING MANUAL SENSITIVITY

Learn how to adjust Manual Sensitivity on the MINELAB GPX 6000 Gold Detector.

MINELAB GPX 6000 TURNING THE THRESHOLD TONE ON /OFF

Learn how to turn the Threshold Tone on and off on the Minelab GPX 6000 gold detector.

GPX 6000 SPEAKER AUDIO

26th Aug 2022
Minelab has identified infrequent cases where users hear audio feedback when using the internal speaker.
Please refer to the product notice on our website by clicking on the link below.

https://www.minelab.com/support/product-notices?article=482551

Minelab have produced a hardware update that removes this effect.
This update is present in all newly manufactured GPX6000s.
In the event you have a production standard without this update and have experienced audio feedback when using the speaker please follow the procedure below in Australia to arrange for this update to be completed on your detector.
Please note for maximum performance headphones should be used.
Headphone performance is unaffected with this update.

Australia:

1. Contact Minelab head office via phone or email.

service@minelab.com.au

(08) 8238 0888

You will need the following information ready to give to Minelab staff:

Full name
Contact phone number
Return postal address
Detector serial number (located on the bottom of the control box)

2. Minelab staff will then determine if your detector already has the hardware update.

3. To have your detector updated you will need to send your detector control box to the following address.

Minelab Service
2 Second Avenue
Mawson Lakes
South Australia
5095

Removing the GPX 6000 Control Box:

*Please note if you are not comfortable removing the control box from the shaft assembly simply send the complete assembly*
To remove the control box from the upper shaft and display assembly please follow the below procedure.

1. Disconnect the coil and remove the lower shafts from the upper shaft.

2. Remove the screw holding the speaker cover in place on the rear of the control box with a medium sized Phillips head screwdriver.

3. Lift the lower part of the speaker cover away from the control box and then lift the speaker cover out of the 2 upper tabs as shown below.

4. Unplug the control box connector and remove the two large Phillips head screws at the top of the control box.

5. Gently slide the control box away from the shaft assembly.

6. Replace the speaker cover on the rear of the control box and tighten the screw. Package and send to Minelab.